TD3063
Zero-Volt Switching
Triac Driver
The TD3063 consists of a single input LED optically coupled to a zero-volt crossing triac driver. The TD3063 provides high input-to-output
isolation and is designed to drive high-powered triacs. Typical uses include interfacing logic level control signals to equipment powered
from 110Vac and 220Vac lines.
DESCRIPTION
FEATURES
APPLICATIONS
OPTIONS/SUFFIXES*
SCHEMATIC DIAGRAM
ABSOLUTE MAXIMUM RATINGS*
APPROVALS
Zero-volt switching
600V blocking voltage
High input-to-output isolation (5kV)
Low trigger current (5mA MAX)
High reliability
Home appliances
Motor/ Drive controls
Solid state relays
Solenoid / Valve control
Temperature Control
Surface Mount Leadform Option
-S
Tape and Reel Option
-TR
Signifies VDE approval
-V
0.4" Lead Spacing (see mechanical dimensio
n)
-H
NOTE: Suffixes listed above are not included in marking on
device for part number identification.
PARAMETER
UNIT
MIN
TYP
MAX
Storage Temperature
C
-55
125
Operating Temperature
C
-40
85
Continuous Input Current
mA
50
Transient Input Current
mA
400
Reverse Input Control
Voltage
V
6
Total Power Dissipation
mW
330
Soldering Temperature
(10s)
C
260
*The values indicated are absolute stress ratings. Functional operation of the
device is not implied at these or any conditions in excess of those defined in
electrical characteristics section of this document. Exposure to Absolute
Ratings may cause permanent damage to the device and may adversely
affect reliability.
1
2
+ Input
- Input
3
6
5
4
+/- AC Output
Do Not Use
-/+ AC Output
UL and C-UL Approved File # E201932
VDE Approved, Lic # 40011225
2004 Solid State Optronics San Jos, CA
www.ssousa.com +1.408.293.4600
Page 1 of 5
TD3063
rev 1.40 (10/25/2004)
TD3063
Zero-Volt Switching
Triac Driver
ELECTRICAL CHARACTERISTICS - 25C
PARAMETER
UNIT
MIN
TYP
MAX TEST CONDITIONS
INPUT SPECIFICATIONS
LED Forward Voltage
V
1.2
1.5
If = 10mA
LED Reverse Voltage
V
6
12
Ir = 10uA
Reverse Leakage Current
10
Vr = 4V
A
OUTPUT SPECIFICATIONS
Blocking Voltage
V
600
Io = 1uA
Peak Blocking Current
n
60
500
Vdrm = Rated
A
On-state Voltage
V
1.8
3
Itm = 100mA
Critical Rate of Rise
V
600
/
s
COUPLED SPECIFICATIONS
Isolation Voltage
V
5000
T = 1 minute
Trigger Current
m
5
Main terminal voltage = 3V
A
Inhibit Voltage
V
5
20
If = 5mA
Isolation Resistance
G
50
DC 500V
Holding Current
100
A
Leakage Current
1
If = Rated, Vdrm = Rated, Off State
A
2004 Solid State Optronics San Jos, CA
www.ssousa.com +1.408.293.4600
Page 2 of 5
TD3063
rev 1.40 (10/25/2004)
TD3063
Zero-Volt Switching
Triac Driver
PERFORMANCE DATA
2004 Solid State Optronics San Jos, CA
www.ssousa.com +1.408.293.4600
Page 3 of 5
TD3063
rev 1.40 (10/25/2004)
Fig.2 Inhibit Voltage versus
Temperature
Ta,AMBIENT TEMPERATURE (C)
V
INH
, NORMALIZED
Fig.1 On-State Characteristics
V
TM
,ON-STATE VOLTAGE (VOLTS)
I
TM
,ON-ST
A
TE CURRENT (mA)
Fig.3 Leakage with LED Off versus
Temperature
Ta,AMBIENT TEMPERATURE (C)
I
DRM1
,PEAK BLOCKING CURRENT (nA)
Fig.5 Trigger Current versus
Temperature
Ta,AMBIENT TEMPERATURE (C)
I
FT
, NORMALIZED
Fig.4 I
DRM2
,Leakage in Inhibit State
versus Temperature
Ta,AMBIENT TEMPERATURE (C)
I
DRM2
NORMALIZED
MECHANICAL DIMENSIONS
2004 Solid State Optronics San Jos, CA
www.ssousa.com +1.408.293.4600
Page 4 of 5 TD3063
rev 1.40 (10/25/2004)
6 PIN DUAL IN-LINE PACKAGE (Through Hole)
6 PIN SURFACE MOUNT DEVICE (SMD)
TOLERANCE :+ 0.25mm
Unit in (mm)
-H Suffix
0.4" Lead Spacing
TD30
63
Zero-Volt Switching
Triac Driver
TD3063
Zero-Volt Switching
Triac Driver
Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO
reserves the right to make changes to product description, specifications at any time without further notice.
SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent
licenses nor indemnity are expressed or implied.
Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other
warranty, expressed or implied, including merchantability and fitness for particular use.
DISCLAIMER
LIFE SUPPORT POLICY
SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or
death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all
damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be
reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system
whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness.
2004 Solid State Optronics San Jos, CA
www.ssousa.com +1.408.293.4600
Page 5 of 5
TD3063
rev 1.40 (10/25/2004)
PDF 
ZIP