STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
10126 - Rev C
DESCRIPTION
STATEK's surface-mount CXO3M oscillator consists of a
CMOS compatible hybrid circuit and a STATEK miniature
quartz crystal in an ultra-low profile ceramic package with one
of the smallest footprints available in the industry.
FEATURES
Designed for surface mount applications using infrared,
vapor phase, wave solder or epoxy mount techniques.
3 Volt operation
TTL and CMOS compatible
Low power consumption
Optional Output Enable or Tri-State
Low EMI emission
High shock resistance
Full military testing available
Hermetically sealed ceramic package
APPLICATIONS
Industrial, Computer & Communications
General purpose clock oscillator
PCMCIA (FAX, Modem and LAN)
Smart Card
PDA and notebook computers
Military & Aerospace
Airborne hybrid computer
Military high speed modem
MCM
CXO3M OSCILLATOR
3 Volt Operation 1.25 MHz to 120 MHz
Ultra-Low Profile (1.3 mm) Miniature
Surface Mount Crystal Oscillator
TM
KM
32M
A
TOP
BOTTOM
2
3
1
4
B
C
D
D
E
TYP.
MAX.
DIM
INCHES
mm
INCHES
mm
A
0.256
6.50
0.263
6.68
B
0.197
5.00
0.204
5.18
C*
0.051
1.30
0.055
1.40
D
0.055
1.40
E
0.060
1.52
0.070
1.78
Termination material is Au over Ni (SMI), solder dip (SM3) also available.
*SMI termination; SM3 = 0.063 in. (1.60 mm) Max.
SUGGESTED LAND PATTERN
PACKAGE DIMENSIONS
.067(1.70)
.070(1.78)
.065(1.65)
.136(3.45)
GRID
PLACEMENT
COURTYARD
.
137(3.48)
.201(5.11)
actual size
side view
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
10126 - Rev C
SPECIFICATIONS
Specifications are typical at 25oC unless otherwise noted.
Specifications are subject to change without notice.
Supply Voltage
3.3V 10% (5V available)
Calibration
A:
0.01% (100ppm)
Tolerance*
B:
0.1%
C:
1.0%
Frequency
0
O
C to +50
O
C from
5 to 30ppm
Stability**
-10
O
C to +70
O
C from 10 to 50ppm
-40
O
C to +85
O
C from
20 to
100ppm
-55
O
C to +125
O
Cfrom 30
to 100ppm
Supply Current
10 mA for 50 MHz
@ 3.3V
8 mA for 40 MHz
6 mA for 30 MHz
4 mA for 24 MHz
TTL Load
10 @ 3 Volts
CMOS Load
15 pF (up to 50 pF available)
Start-up Time
5 msec. MAX.
Rise/Fall Time
3 nsec. Typ., 6 nsec. MAX.
Duty Cycle
40% Min., 60% MAX.
Aging, first year
10 ppm MAX.
Shock, survival***
3,000g peak 0.3 msec., 1/2 sine
Vibration survival
20g rms 10-2000 Hz random
Operating Temperature -10
O
C to +70
O
C Commercial
-40
O
C to +85
O
C Industrial
-55
O
C to +125
O
C Military
* Tighter tolerances available
** Does not include calibration tolerances
*** High shock version available
Note: all parameters are measured at ambient temperature
with a 10M
and 10pF load at 5V
PACKAGING
CX03M
- Tray Pack (Standard)
- 16mm tape, 7" or 13" reels (Optional)
Per EIA 481 (see data sheet 10109)
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
ABSOLUTE MAXIMUM RATINGS
Supply Voltage V
DD
-0.5V to 7.0V
Storage Temperature
-55
O
C to +125
O
C
Maximum Process Temperature 260
O
C, 10 seconds
TRUTH TABLE
PIN 1*
PIN 3
CXO3M-10E
Low (0)
High (Z)
High (1)
Freq. Output
CXO3M-10T
Low (0)
High (Z)
High (1)
Freq. Output
CXO3M-10N
NC
Freq. Output
* Normally high (internal pull-up resistor)
ENABLE VS. TRI-STATE
Enable: When pin 1 is low (0), the oscillator stops
oscillation.
Tri-state: When pin 1 is low, the oscillator is running.
However, the output buffer amplifier stops
functioning and output is in high impedance
(Z) state.
Enable
Tri-state
Current consumption
when pin 1 is low
Low
High
Output recovery delay
when pin 1 changes from
Delayed
Immediate
low (0) to high (1)
PIN CONNECTIONS
1. Output Enable, INH (Tri-State) or NC
2. Ground
3. Output
4.
V
DD
___
HOW TO ORDER CXO3M SURFACE MOUNT CRYSTAL OSCILLATORS
CXO3M
S
10
T
SM3
32 MHz
(
100ppm
/
200ppm
/
200ppm
/
I
)
* Enable available over 10MHz
** Other calibration fill in ppm
Frequency
Temp. Range:
C = Commercial
I = Industrial
M = Military
S = Special
Total Frequency
Tolerance
Frequency
Stability over
Temp. Range
**Calibration
Tolerance
@ 25
0
C
(A)
(B)
(C)
*E = Enable
T = Tri-State
N = Neither
Blank = SM1(std.)
SM1 = Gold Plated
SM3 = Solder Dipped
10 = 10 TTL Load
"S" if special
or custom
design.
Blank if Std.
PDF 
ZIP