2002-02-25 Page
1
MDST-0017-02
TLSI Incorporated, 770 Park Avenue
,
Huntington NY 11743
(631) 755-7005
Fax 631-755-7626
www.tlsi.com
Applications
Low cost general-purpose clock source
General Description
The T98521 is a 3.3V CMOS, clock multiplier integrated circuit. The device provides an excellent quality
high frequency output clock from a lower frequency crystal or clock input. Tri-level selection inputs S0 and
S1 are used to select any one of eight multipliers, stored in the on-board ROM, and apply it to the input to
produce the desired output, up to 220 MHz. Phase Locked Loop (PLL) technology allows the device to use
an input signal from an inexpensive crystal. When Output Enable (OE) is low, the clock output is in high
impedance state.
The T98521, when used with an inexpensive crystal, provides a cost-effective clock source for most
electronic systems.
Figure 1. Functional Block Diagram
T98521
3.3V Clock Multiplier
Features
Low phase noise
Zero ppm multiplication error
Input clock frequency 5 - 50 MHz.
Input crystal frequency 5 27 MHz
Output clock frequencies up to 220 MHz.
5V-tolerant inputs and output
Fully Compatible with all popular CPUs
Duty Cycle - 45/55 up to 160 MHz.
- 40/60 160 MHz to 220 MHz
25mA drive capability at TTL levels
High-Z output for board level testing
X1/ICLK
VDD
S0
S1
Output Enable
Clock or
Xtal
input
PLL
Clock
Multiplier
&
ROM
Output
Buffer
Xtal.
Osc.
GND
X2
Optional
caps
CLK
Figure 2. Pin Assignment
1
2
3
4
8
7
6
5
X1/ICLK
VDD
GND
S1
X2
OE
S0
CLK
8-pin SOIC/MSOP
T98521
2002-02-25 Page
2
MDST-0017-02
TLSI Incorporated, 770 Park Avenue
,
Huntington NY 11743
(631) 755-7005
Fax 631-755-7626
www.tlsi.com
Table 2. Pin Description
No. Name
Type Description
1
X1/ICLK
I
Xtal connection or clock input.
2 VDD P Connect
to
+3.3V
3 GND P Connect
to
ground.
4
S1
TI
Select 1 for output clock. Connect to ground or VDD or float
5
CLK
O
Clock output per table 2.
6
S0
TI
Select 0 for output clock. Connect to ground or VDD or float.
7
OE
I
Output Enable. Tri- states CLK output when low.
8
X2
O
Xtal connection. Leave unconnected for clock input.
Legend:
I = Input
TI = Tri-level Input
O = Output
P = Power supply connection
Table 3. Absolute Maximum Ratings
Parameter Conditions
Min
Typ
Max
Units
Supply voltage, VDD
Referenced to GND
4.6
V
Inputs and Clock Outputs
Referenced to GND
-0.5
4.6
V
Soldering Temperature
Max of 10 seconds
260
C
Storage temperature
-65
150
C
Table 1. Clock Output Table
S1 S0 CLK
Minimum
Input
0 0 4
x
input
See
table
6
0
M
5.3125 x input 20 MHz
0 1 5
x
input
See
table
6
M
0
6.25 x input
4 MHz
M M Test*
M
1
3.125 x input
8 MHz
1 0 6
x
input
See
table
6
1
M
3 x input
See table 6
1 1 8
x
input
See
table
6
0 = Connect to ground.
1 = Connect directly to VDD
M = Leave unconnected (floating)
* = For TLSI internal test purposes only
T98521
2002-02-25 Page
3
MDST-0017-02
TLSI Incorporated, 770 Park Avenue
,
Huntington NY 11743
(631) 755-7005
Fax 631-755-7626
www.tlsi.com
Table 4. Operating Conditions
Parameter Min
Typ
Max
Units
Ambient Operating Temperature
0
70
C
Operating Voltage, VDD
3
3.6
V
Input High Voltage, V
IH
, X1 pin only
2.5
1.65
V
Input Low Voltage, V
IL
, X1 pin only
1.65
0.5
V
Input High Voltage, V
IH
, OE pin
2
V
Input Low Voltage, V
IL
, OE pin
0.8
V
Input High Voltage, V
IH
, trinary inputs
VDD-0.5
V
Input Low Voltage, V
IL
, trinary inputs
0.5
V
DC Characteristics
Table 5. DC Characteristics
VDD = 3V to 3.6V
Parameter Condition
Min
Typ
Max
Units
Output High Voltage, V
OH
I
OH
=-25mA 2.4
V
Output Low Voltage, V
OL
I
OL
=25mA
0.4
V
Operating Supply Current, I
DD
(20 MHz Xtal)
No Load, 100MHz
25
mA
Short Circuit Current
CLK output
100
mA
Input Capacitance
S0, S1, OE, X1, X2
4
pF
Frequency synthesis error
0
ppm
T98521
2002-02-25 Page
4
MDST-0017-02
TLSI Incorporated, 770 Park Avenue
,
Huntington NY 11743
(631) 755-7005
Fax 631-755-7626
www.tlsi.com
AC Characteristics
Table 6 AC Characteristics
VDD = 3V to 3.6V over the operating temperature range
Symbol Parameter
Condition
Min
Typ
Max
Units
f
osc
Input Crystal Frequency
5
27
MHz
f
in
Input
clock
frequency
5
50
MHz
f
out
Output Frequency,
24
220
MHz
t
r
Output Clock Rise Time
0.8 to 2.0V
1
ns
t
f
Output Clock Fall Time
2.0 to 0.8V
1
ns
up to 160 MHz
45 49 to 51 55
%
t
od
Output Clock Duty Cycle
1.5 V
160 MHz to 220 MHz
40
60
%
PLL
Bandwidth
10
kHz
T
PZH,
T
PZL
Output Enable Time, OE high to output on
50
ns
T
PHZ,
T
PLZ
Output Disable time, OE low to Tri-state
50
ns
t
jit
(abs)
Absolute Clock period Jitter
Deviation from mean
f
out
= 160 MHz
70 ps
t
jit
(sigma)
One Sigma Clock Period Jitter
f
out
= 160 MHz
25
ps
Note1: External Crystal Connection
.
The external crystal should be connected in as close physical proximity to the T98521 as possible. The crystal should be a
fundamental mode, parallel resonant. Do not use third overtone. External load capacitors should be fitted in accordance with the
crystal manufacturer's specifications.
Note2: Decoupling and termination
.
Decoupling capacitors of 0.01
F and 0.1
F should be connected between VDD and Ground. Capacitors should be mounted as
close to the chip as possible. A 33 termination resistor may be connected in series with the clock output in order to minimize ringing
and reflections.
Figure 3. External Crystal Connection Block Diagram
Crystal
CLK3
106.25MHz
X2
X1
33pF
C
X1
XTAL OSC
PLL
CLOCK
GEN.
OE
External Crystal
Load Capacitors
CLK
X2
X1
C
X2
C
X1
XTAL OSC
PLL
OE
External Crystal
Load Capacitors
T98521
2002-02-25 Page
5
MDST-0017-02
TLSI Incorporated, 770 Park Avenue
,
Huntington NY 11743
(631) 755-7005
Fax 631-755-7626
www.tlsi.com
Package Dimensions.
Ordering Information
Part Number
Marking
Shipping/Packaging
No. of Pins
Package
Temperature
T98521S1 T98521S1 Tubes
8
SOIC 0
o
C to +70
o
C
T98521S1X
T98521S1
Tape & Reel
8
SOIC
0
o
C to +70
o
C
T98521M T98521M Tubes
8
MSOP 0
o
C to +70
o
C
T98521MX
T98521M
Tape & Reel
8
MSOP
0
o
C to +70
o
C
T98521/D
Dice in waffle-packs
0
o
C to +70
o
C
T98521/DW
Dice in wafer form
0
o
C to +70
o
C
MSOP
SOIC
All dimensions are in millimeters
All dimensions are in millimeters
VARIATIONS
(ALL ARE IN MM)
AA
SYM
BO
L
S
MIN NOM MAX
A 1.35 1.55 1.75
A1 .011 -
0.25
B 0.33 0.42 0.51
C 0.19 0.22 0.25
D 4.80 4.90 5.00
E1 3.80 3.90 4.00
e 1.27
BSC
E 5.80 6.00 6.20
h 0.25 0.38 0.50
oc 0 5 8
L 0.40 - 1.27
N 8
VARIATIONS
(ALL ARE IN MM)
AA
SYM
BO
L
S
MIN NOM MAX
A - - 1.1
A1 0 - 0.15
A2 0.75 0.85 0.95
b 0.22 - 0.38
c 0.08 - 0.23
D 3.00
BSC
E 4.90
BSC
E1 3.00
BSC
L 0.4 0.6 0.8
e 0.65
oc 0 - 8
OC1 5
-
15
PDF 
ZIP