ChipFind - документация

Электронный компонент: 856070

Скачать:  PDF   ZIP
Preliminary Data Sheet
Part Number 856070
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev -
27-Aug-2002
Page 1 of 5
Features
For broadband applications
Typical 3 dB bandwidth of 14.1 MHz
High attenuation
No impedance matching required for operation
at 50
Single-ended operation
Ceramic Surface Mount Package (SMP)
Small size
Replaces Sawtek P/N 851925 (BW 3dB=14 MHz)
Package
Pin Configuration
Surface Mount 13.30 x 6.50 x 1.50 mm
Bottom View
6
7
8
9
10
5
4
3
2
1
Pin No. Description
5
Output
10
Input
1,6
Ground
2,3,4
Case
ground
7,8,9
Case
ground
1.80
6.50
1.02
1.91
13.3
2.31
R0.51
1.50 NOM.
1.65 MAX.
0.64
Dimensions shown are nominal in millimeters
All tolerances are
0.15mm except overall
length and width
0.10mm
Body: Al
2
O
3
ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 0.5 - 1.0
m,
over a 2 - 6
m Ni plating
Preliminary Data Sheet
Part Number 856070
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev -
27-Aug-2002
Page 2 of 5
Electrical Specifications
(1)

Operating Temperature Range:
(2)
0 to +70
o
C
Parameter
(3)
Minimum
Typical
Maximum
Unit
Center Frequency
- 140 -
MHz
Minimum Insertion Loss
- 23.3
24.5
dB
Lower 1 dB Bandedge
(4)
Upper 1 dB Bandedge
-
145.89
133.26
146.67
134.11
-
MHz
MHz
Lower 3 dB Bandedge
(4)
Upper 3 dB Bandedge
-
146.23
132.93
147.00
133.77
-
MHz
MHz
Lower 40 dB Bandedge
(4)
Upper 40 dB Bandedge
130.87
-
131.58
148.33
-
149.13
MHz
MHz
Amplitude Variation
134.11 - 145.89
MHz
-
0.31
0.70
dB
Phase Linearity
134.11 - 145.89
MHz
-
2.06
6.00
deg
Group Delay Variation
134.11 - 145.89
MHz
-
27
55
nsec
Absolute Delay
- 1.50 -
sec
Relative Attenuation
(4)
15
-
50
MHz
50
-
127
MHz
156
-
240
MHz
240
-
290
MHz
290
-
310
MHz
310
-
350
MHz
42
48
48
43
42
44
49
55
53
49
48
48
-
-
-
-
-
-
dB
dB
dB
dB
dB
dB
Source Impedance
(5)
- 50 -
Load Impedance
(5)
- 50 -
Substrate Material
- YZ
LiNbO
3
- -
Temperature Coefficient of Frequency
- -94 -
ppm/
o
C

Notes:
1. All specifications are based on the test circuit shown below
2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over
temperature
3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances
4. All attenuation measurements are measured relative to minimum insertion loss
5. This is the optimum impedance in order to achieve the performance shown

Test Circuit:
Actual matching values may vary due to PCB layout and parasitics


50
Single-ended
1,2,3,4
6,7,8,9
50
10
5
50
Preliminary Data Sheet
Part Number 856070
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev -
27-Aug-2002
Page 3 of 5
Typical Performance
(at +25
o
C)
Preliminary Data Sheet
Part Number 856070
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev -
27-Aug-2002
Page 4 of 5
Matching Schematics
Actual matching values may vary due to PCB layout and parasitics
50
Single-ended
1,2,3,4
6,7,8,9
50
10
5
50
Marking
PCB Footprint
XXXXXX
856070
SAWTEK
2.00
1.22
.69
8.84
6.70
The date code consists of: day of the current year (Julian,
3 digits), last digit of the year (1 digit) and hour (2 digits)
This footprint represents a recommendation only
Dimensions shown are nominal in millimeters
Tape and Reel
A
A
24
1.75
11.5
1.5
2.3
13.9
4.0
1.5
2.0
0.3
12.0
7.1
Section A-A
Direction of travel
330
24.8
2.7
102
13.0
20.2
2.0
ID dot
Dimensions shown are nominal in millimeters
Packaging quantity: 2000 units/reel
Preliminary Data Sheet
Part Number 856070
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev -
27-Aug-2002
Page 5 of 5
Maximum Ratings
Parameter
Symbol Minimum
Typical
Maximum
Unit
Operating Temperature Range
T
0
+25
+70
o
C
Storage Temperature Range
T
stg
-40 -
+85
o
C
Warnings
Electrostatic Sensitive Device (ESD)
Avoid ultrasonic exposure
Links to Additional Technical Information
PCB Layout Tips
Qualification Flowchart
Soldering Profile
S-Parameters
Other Technical Information
Sawtek's liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. Sawtek does not accept any liability for
applications, processes, circuits or assemblies which are implemented using any Sawtek component described in this data sheet.
Contact Information
PO Box 609501
Orlando, FL 32860-9501
USA
Phone: +1 (407) 886-8860
Fax: +1 (407) 886-7061
Email:
custservice@sawtek.com
Web:
www.sawtek.com
Or contact one of our worldwide
network of
sales offices,
representatives or distributors