www.vishay.com
127
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
Solid Tantalum Chip Capacitors
T
ANTAMOUNT
, Conformal Coated
FEATURES
Pad compatible with 194D and MIL-C-556365/4 (CWR06).
8mm, 12mm 16mm Tape to EIA-481-2 and reeling per IEC
286-3. 7" [178mm] standard. 13" [330mm] available.
Terminations: Tin (2) standard.
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55C to + 85C. (To + 125C
with voltage derating.)
Capacitance Range: .10F to 270F
CASE
CODE
A
B
D
E
F
G
H
DIMENSIONS
in inches [millimeters]
J
W
Tantalum Wire Nib
Identifies Anode (+)
Terminal
J
H
A
L
B
D
L (Max.)
0.135
[3.4]
0.185
[4.7]
0.185
[4.7]
0.235
[6.0]
0.255
[6.5]
0.300
[7.6]
0.303
[7.7]
W
0.050 0.015
[1.27 0.38]
0.050 0.015
[1.27 0.38]
0.095 0.015
[2.41 0.38]
0.095 0.015
[2.41 0.38]
0.135 0.015
[3.43 0.38]
0.100 0.015
[2.54 0.38]
0.150 0.015
[3.81 0.38]
H
0.050 .015
[1.27 0.38]
0.050 0.015
[1.27 0.38]
0.050 0.015
[1.27 0.038]
0.050 0.015
[1.27 0.38]
0.070 0.015
[1.78 0.38]
0.100 0.015
[2.54 0.38]
0.110 0.015
[2.79 0.38]
A
0.023 0.010
[0.584 0.25]
0.040 0.015
[1.02 0.38]
0.040 0.015
[1.02 0.38]
0.040 0.015
[1.02 0.38]
0.040 0.015
[1.02 0.38]
0.040 0.015
[1.02 0.38]
0.050 0.015
[1.27 0.38]
B
0.067 0.015
[1.70 0.38]
0.120 0.015
[3.05 0.38]
0.110 0.020
[2.79 0.51]
0.170 0.020
[4.32 0.51]
0.185 0.020
[4.70 0.51]
0.220 0.020
[5.59 0.51]
0.220 0.020
[5.59 0.51]
D (Ref.)
0.100
[2.54]
0.150
[3.81]
0.140
[3.56]
0.200
[5.08]
0.220
[5.59]
0.260
[6.60]
0.265
[6.73]
J (Max.)
0.004
[0.10]
0.004
[0.10]
0.004
[0.10]
0.004
[0.10]
0.004
[0.10]
0.004
[0.10]
0.004
[0.10]
Note: The anode termination (D less B) will be a minimum of 0.010" [0.3mm]. T Case = 0.005" [0.13mm] minimum.
ORDERING INFORMATION
T = Tape and Reel
7" [178mm] Reel
W = 13" [330mm] Reel
(1/2 reel minimum)
See Tape and Reel Specifications
T
PACKAGING
2 = 100% Tin.
4 = Gold Plated.
8 = Solder Plated
(60/40) Special
Order.
2
TERMINATION
See Ratings
and Case
Codes Table.
A
CASE CODE
004
DC VOLTAGE RATING
@ + 85C
This is expressed in volts.
To complete the three-
digit block, zeros precede
the voltage rating.
X0
CAPACITANCE
TOLERANCE
This is expressed in picofarads.
The first two digits are the
significant figures. The third is the
number of zeros to follow.
475
CAPACITANCE
X0 =
20%
X9 = 10%
695D
TYPE
NOTE: Preferred Tolerances and reel sizes are in bold.
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Voltage
substitutions will be marked with the higher voltage rating.
Capacitance Tolerance: 10%, 20% standard.
Voltage Rating: 4 WVDC to 50 WVDC.
www.vishay.com
128
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
F
RATINGS AND CASE CODES
4.7
6.8
10
15
22
33
47
68
100
120
150
180
220
270
4 WVDC @ + 85
C, SURGE = 5.2 V . . . 2.7 WVDC @ + 125
C, SURGE = 3.4 V
CAPACITANCE
(
F)
Max. RIPPLE
100kHz
Irms
(Amps)
Max. ESR
@ + 25
C
100kHz
(Ohms)
Max. DF
@ + 25
C
120 Hz
(%)
Max. DCL
@ + 25
C
(
A)
PART NUMBER*
STANDARD RATINGS
CASE
CODE
0.5
0.5
0.5
0.6
0.9
1.3
1.9
2.7
4.0
4.8
6.0
7.2
8.8
10.8
6
6
6
6
6
6
6
6
8
8
8
8
8
8
11
9
8.5
2.2
2
1.5
1
0.9
0.9
0.7
0.65
0.4
0.35
0.35
0.07
0.09
0.09
0.20
0.21
0.25
0.33
0.35
0.35
0.41
0.43
0.61
0.65
0.65
695D475X_004A2T
695D685X_004B2T
695D106X_004B2T
695D156X_004D2T
695D226X_004D2T
695D336X_004E2T
695D476X_004F2T
695D686X_004F2T
695D107X_004F2T
695D127X_004G2T
695D157X_004G2T
695D187X_004H2T
695D227X_004H2T
695D277X_004H2T
A
B
B
D
D
E
F
F
F
G
G
H
H
H
6 V
10 V
15 V
20 V
25 V
35 V
50 V
A
B
B
D
D
E
F
F
F
G
G
H
H
H
A
B
D
D
D
E
F
F
G
G
H
H
H
A
B
D
D
D
E
F
F
G
G
H
H
A
A
B
D
D
D
E
F
F
G
H
H
A
B
B
D
D
E
F
F
G
G
H
A
A
B
D
D
D
E
F
F
G
H
H
A
A
B
B
D
D
E
F
F
F
G
H
A
A
B
B
D
D
D
E
F
F
G
H
H
4 V
For 10% tolerance, specify "9"; for 20% tolerance, change to "0".
6 WVDC @ + 85
C, SURGE = 8 V . . . 4 WVDC @ + 125
C, SURGE = 5 V
0.10
0.15
0.22
0.33
0.47
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
120
150
180
220
270
4.7
6.8
A
B
695D475X_006A2T
695D685X_006B2T
0.5
0.5
6
6
11
9
0.07
0.07
www.vishay.com
129
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
CAPACITANCE
(
F)
Max. RIPPLE
100kHz
Irms
(Amps)
Max. ESR
@ + 25
C
100kHz
(Ohms)
Max. DF
@ + 25
C
120 Hz
(%)
Max. DCL
@ + 25
C
(
A)
PART NUMBER*
STANDARD RATINGS
CASE
CODE
G
G
H
H
6.8
10
12
15
6
8
8
8
0.75
0.75
0.45
0.40
68
100
120
150
695D686X_010G2T
695D107X_010G2T
695D127X_010H2T
695D157X_010H2T
11.5
10.6
2.6
2.5
2.2
2
1.2
1
15 WVDC @ + 85
C, SURGE = 20 V . . . 10 WVDC @ + 125
C, SURGE = 12 V
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
A
A
B
D
D
D
E
F
F
G
H
H
695D155X_015A2T
695D225X_015A2T
695D335X_015B2T
695D475X_015D2T
695D685X_015D2T
695D106X_015D2T
695D156X_015E2T
695D226X_015F2T
695D336X_015F2T
695D476X_015G2T
695D686X_015H2T
695D107X_015H2T
0.5
0.5
0.5
0.7
1
1.5
2.3
3.3
5
7.1
10.2
15
6
6
6
6
6
6
6
6
6
6
6
8
14
12
10.8
2.8
2.6
2.5
2.3
1.4
1.2
0.8
0.5
0.45
0.07
0.07
0.08
0.17
0.18
0.18
0.20
0.28
0.30
0.39
0.55
0.58
20 WVDC @ + 85
C, SURGE = 26 V . . . 13 WVDC @ + 125
C, SURGE = 16 V
1.0
1.5
2.2
3.3
A
B
B
D
695D105X_020A2T
695D155X_020B2T
695D225X_020B2T
695D335X_020D2T
0.5
0.5
0.5
0.7
4
6
6
6
15
12
11
3
0.06
0.08
0.08
0.17
10 WVDC @ + 85
C, SURGE = 13 V . . . 7 WVDC @ + 125
C, SURGE = 8 V
3.3
4.7
6.8
10
15
22
33
47
A
B
D
D
D
E
F
F
695D335X_010A2T
695D475X_010B2T
695D685X_010D2T
695D106X_010D2T
695D156X_010D2T
695D226X_010E2T
695D336X_010F2T
695D476X_010F2T
0.5
0.5
0.7
1.0
1.5
2.2
3.3
4.7
6
6
6
6
6
6
6
6
0.07
0.08
0.18
0.18
0.20
0.22
0.30
0.33
10
15
22
33
47
68
100
120
150
180
220
D
D
D
E
F
F
G
G
H
H
H
695D106X_006D2T
695D156X_006D2T
695D226X_006D2T
695D336X_006E2T
695D476X_006F2T
695D686X_006F2T
695D107X_006G2T
695D127X_006G2T
695D157X_006H2T
695D187X_006H2T
695D227X_006H2T
0.6
0.9
1.3
2.0
2.8
4.1
6.0
7.2
9.0
10.8
13.2
6
6
6
6
6
6
8
8
8
8
8
8.5
2.2
2
1.5
1
0.9
0.9
0.7
0.65
0.4
0.35
For 10% tolerance, specify "9"; for 20% tolerance, change to "0".
6 WVDC @ + 85
C, SURGE = 8 V . . . 4 WVDC @ + 125
C, SURGE = 5 V
0.1
0.2
0.32
0.25
0.33
0.35
0.37
0.41
0.48
0.61
0.65
0.40
0.40
0.58
0.61
www.vishay.com
130
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
25 WVDC @ + 85
C, SURGE = 32 V . . . 17 WVDC @ + 125
C, SURGE = 20 V
0.47
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
A
A
B
D
D
D
E
F
F
G
H
H
695D474X_025A2T
695D684X_025A2T
695D105X_025B2T
695D155X_025D2T
695D225X_025D2T
695D335X_025D2T
695D475X_025E2T
695D685X_025F2T
695D106X_025F2T
695D156X_025G2T
695D226X_025H2T
695D336X_025H2T
0.5
0.5
0.5
0.5
0.6
0.8
1.2
1.7
2.5
3.8
5.5
8.3
4
4
4
6
6
6
6
6
6
6
6
6
17
15
13
4.2
3.5
3
2.75
2
1.8
1
0.7
0.8
0.06
0.06
0.08
0.14
0.16
0.17
0.19
0.23
0.25
0.35
0.46
0.50
35 WVDC @ + 85
C, SURGE = 46 V . . . 23 WVDC @ + 125
C, SURGE = 28 V
0.22
0.33
0.47
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
15
A
A
B
B
D
D
E
F
F
F
G
H
695D224X_035A2T
695D334X_035A2T
695D474X_035B2T
695D684X_035B2T
695D105X_035D2T
695D155X_035D2T
695D225X_035E2T
695D335X_035F2T
695D475X_035F2T
695D685X_035F2T
695D106X_035G2T
695D156X_035H2T
0.5
0.5
0.5
0.5
0.5
0.5
0.8
1.2
1.6
2.4
3.5
5.3
4
4
4
4
4
6
6
6
6
6
6
6
20
18
15
14
8
4.2
4
3.2
2.7
2
1.3
0.8
0.05
0.06
0.07
0.07
0.10
0.14
0.15
0.19
0.20
0.23
0.30
0.43
50 WVDC @ + 85
C, SURGE = 65 V . . . 33 WVDC @ + 125
C, SURGE = 38 V
0.10
0.15
0.22
0.33
0.47
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
A
A
B
B
D
D
D
E
F
F
G
H
H
695D104X_050A2T
695D154X_050A2T
695D224X_050B2T
695D334X_050B2T
695D474X_050D2T
695D684X_050D2T
695D105X_050D2T
695D155X_050E2T
695D225X_050F2T
695D335X_050F2T
695D475X_050G2T
695D685X_050H2T
695D106X_050H2T
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
1.1
1.7
2.4
3.4
5.0
4
4
4
4
4
4
4
6
6
6
6
6
6
32
30
18
16
9
8.5
8
5.5
3.9
3.2
2.5
1.2
1
0.04
0.04
0.06
0.07
0.10
0.10
0.10
0.13
0.17
0.19
0.22
0.35
0.39
*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0".
0.17
0.19
0.25
0.27
0.37
0.39
0.55
2.8
2.55
1.8
1.5
0.9
0.8
0.5
6
6
6
6
6
6
6
0.9
1.4
2.0
3.0
4.4
6.6
9.4
695D475X_020D2T
695D685X_020E2T
695D106X_020F2T
695D156X_020F2T
695D226X_020G2T
695D336X_020G2T
695D476X_020H2T
D
E
F
F
G
G
H
4.7
6.8
10
15
22
33
47
CAPACITANCE
(
F)
Max. RIPPLE
100kHz
Irms
(Amps)
Max. ESR
@ + 25
C
100kHz
(Ohms)
Max. DF
@ + 25
C
120 Hz
(%)
Max. DCL
@ + 25
C
(
A)
PART NUMBER*
STANDARD RATINGS
CASE
CODE
20 WVDC @ + 85
C, SURGE = 26 V . . . 13 WVDC @ + 125
C, SURGE = 16 V
www.vishay.com
131
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
TYPICAL CURVES @ + 25C, IMPEDANCE AND ESR VS FREQUENCY
IMPEDANCE
ESR
IMPEDANCE
ESR
IMPEDANCE
ESR
IMPEDANCE
ESR
.15
F, 50 VDC
3.3
F, 50 VDC
6.8
F, 5 VDC
.33
F, 50 VDC
1.5
F, 50 VDC
22
F, 10 VDC
1
F, 50 VDC
22
F, 6 VDC
100
1K
10K
100K
1M
100
1K
10K
100K
1M
100
1K
10K
100K
1M
100
1K
10K
100K
1M
10000
1000
100
10
1
10000
1000
100
10
1
1000
100
10
1
0.1
100
10
1
0.1
IMPEDANCE
ESR
IMPEDANCE
ESR
IMPEDANCE
ESR
4.7
F, 35 VDC
33
F, 10 VDC
4.7
F, 50 VDC
100
F, 10 VDC
6.8
F, 50 VDC
220
F, 6 VDC
100
1K
10K
100K
1M
100
1K
10K
100K
1M
100
1K
10K
100K
1M
10
1
0.1
0.01
100
10
1
0.1
0.01
100
10
1
0.1
0.01
100
1000
"A CASE"
"B CASE"
"E CASE"
"D CASE"
OHMS
OHMS
OHMS
OHMS
FREQUENCY IN HERTZ
FREQUENCY IN HERTZ
FREQUENCY IN HERTZ
FREQUENCY IN HERTZ
"F CASE"
"G CASE"
FREQUENCY IN HERTZ
FREQUENCY IN HERTZ
OHMS
OHMS
"H CASE"
FREQUENCY IN HERTZ
OHMS
www.vishay.com
132
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
1.0
Operating Temperature: Capacitors are designed to
operate over the temperature range - 55C to + 85C.
1.1
Capacitors may be operated to + 125C with
voltage derating to two-thirds the + 85C rating.
2.0
DC Working Voltage: The DC working voltage is the
maximum operating voltage for continuous duty at the
rated temperature.
3.0
Surge Voltage: The surge DC rating is the maximum
voltage to which the capacitors may be subjected
under any conditions, including transients and peak
ripple at the highest line voltage.
3.1
Surge Voltage Test: Capacitors shall withstand
the surge voltage applied in series with a 33 ohm
5% resistor at the rate of one-half minute on,
one-half minute off, at + 85C, for 1000 successive
test cycles.
3.2
Following the surge voltage test, the dissipation
factor and the leakage current shall meet the initial
requirements; the capacitance shall not have changed
more than 10%.
4.0
Capacitance Tolerance: The capacitance of all
capacitors shall be within the specified tolerance
limits of the normal rating.
4.1
Capacitance measurements shall be made by means
of polarized capacitance bridge. The polarizing
voltage shall be of such magnitude that there shall be
no reversal of polarity due to the AC component. The
maximum voltage applied to capacitors during
measurement shall be 2 volts rms at 120 Hz at +25C.
If the AC voltage applied is less than one-half volt rms,
no DC bias is required. Accuracy of the bridge shall
be within 2%.
6.0
Dissipation Factor: The dissipation factor,
determined from the expression 2fRC, shall not
exceed values listed in the Standard Ratings Table.
6.1
Measurements shall be made by the bridge method
at, or referred to, a frequency of 120 Hz and a
temperature of + 25C.
7.0
Leakage Current: Capacitors shall be stabilized at
the rated temperature for 30 minutes. Rated voltage
shall be applied to capacitors for 5 minutes using a
steady source of power (such as a regulated power
supply) with 1000 ohm resistor connected in series
with the capacitor under test to limit the charging
current. Leakage current shall then be measured.
Note that the leakage current varies with temperature
and applied voltage. See graph below for the
appropriate adjustment factor.
+ 85
C Rating
+ 125
C Rating
Working
Voltage
(V)
Working
Voltage
(V)
Surge
Voltage
(V)
Surge
Voltage
(V)
4
6
10
15
20
25
35
50
5.2
8
13
20
26
32
46
65
2.7
4
7
10
13
17
23
33
3.4
5
8
12
16
20
28
38
- 55C
- 10%
+ 85C
+ 10%
+ 125C
+ 12%
PERFORMANCE CHARACTERISTICS
TYPICAL LEAKAGE CURRENT FACTOR RANGE
5.0
Capacitance Change With Temperature: The
capacitance change with temperature shall not exceed
the following percentage of the capacitance measured
at + 25C:
100
10
1.0
0.1
0.01
0.001
0 10 20 30 40 50 60 70 80 90 100
+ 125
C
+ 85
C
+ 55
C
+ 25
C
0
C
- 55
C
Percent of Rated Voltage
Leakage Current Factor
www.vishay.com
133
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
1.0
Recommended voltage derating guidelines:
(-55C to + 85C)
Standard Conditions, for example; output filters
Capacitor Voltage Rating (V) Operating Voltage (V)
4
2.5
6.3
3.6
10
6
16
10
20
12
25
15
35
24
50
28
Severe Conditions, for example; input filters
Capacitor Voltage Rating (V) Operating Voltage (V)
4
2.5
6.3
3.3
10
5
16
8
20
10
25
12
35
15
50
24
2.0.
A-C Ripple Current: The maximum allowable
ripple current shall be determined from the
formula:
GUIDE TO APPLICATION
P
R
ESR
I
rms
=
8.0
Life Test: Capacitors shall be able to withstand rated
DC voltage applied at +85C for 2000 hours or
derated DC voltage applied at +125C for 1000 hours.
8.1
Following the life test, the capacitance change shall
not exceed 10% of the initial value; the dissipation
factor and leakage current shall meet the initial
requirement; the leakage current shall not exceed
125% of the initial requirement
9.0
Humidity Test: Capacitors shall withstand 1000
hours at + 40C, 90% to 95% relative humidity, with no
voltage applied.
9.1
Following the humidity test, capacitance change shall
be within 10% of the initial value; the dissipation factor
shall not exceed 150% of the initial requirement; the
leakage current shall not exceed 200% of the initial
requirement at + 25C.
10.0
Soldering Testing:Capacitors shall be checked by
the following method: Terminations are immersed in
PERFORMANCE CHARACTERISTICS
(Continued)
Z
V
rms
=
P
R
ESR
non-activated flux and dipped in 60/40 Sn/Pb solder
for 5 seconds at +245C Wetting must occur on at
least 95% of the external surface of the terminations.
11.0
Resistance to Soldering Heat: Capacitors mounted
on a substrate will withstand exposure to +260C for 5
seconds.
11.1
Following the resistance to soldering heat test,
capacitance shall be within initial tolerance; dissipation
factor shall be within 120% of initial requirement at
+25C; the leakage current shall be within initial
requirement at +25C.
12.0
Marking: The small body area of the capacitor does
not allow elaborate marking schemes. All required
information is present on the carton or package in
which the parts are shipped; in addition, part number,
quantity and date code are indicated on the reels.
where,
P =
Power Dissipation in Watts @ + 25C as
given in the table in Paragraph Number 5
(Power Dissipation).
R
ESR
=
The capacitor Equivalent Series Resistance
at the specified frequency.
3.0.
A-C Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
R
ESR
= The capacitor Equivalent Series Resistance
at the specified frequency.
Z =
The capacitor Impedance at the specified
frequency.
3.1
The sum of the peak AC voltage plus the DC voltage
shall not exceed the DC voltage rating of the capaci-
tor.
3.2
The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 10% of the DC working voltage at + 25C.
4.0.
Reverse Voltage: These capacitors are capable of
withstanding peak voltages in the reverse direction
www.vishay.com
134
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
GUIDE TO APPLICATION
(Continued)
equal to 10% of the DC rating at + 25C and 5% of the
DC rating at + 85C and 1% of the DC rating at +85C
and 1% of the DC rating at +125C.
5.0.
Temperature Derating: If these capacitors are to be
operated at temperatures above + 25C, the
permissible rms ripple current or voltage shall be
calculated using the derating factors as shown:
6.0. Power Dissipation: Power dissipation will be
affected by the heat sinking capability of the mounting
surface. Non-sinusoidal ripple current may produce
heating effects which differ from those shown. It is
important that the equivalent
Irms
value be
established when calculating permissible operating
levels. (Power dissipation calculated using + 25C
temperature rise.)
7.0 Printed Circuit Board Materials: The 695D is
compatible with most commonly used printed circuit
board materials (alumina substrates, FR4, FR5, G10,
PTFE-fluorocarbon and porcelanized steel). If your
desired board material is not shown there, please
contact the Tantalum Marketing Department for
assistance in determining compatibility.
8.0. Attachment:
8.1 Solder Paste: The recommended thickness of the
solder paste after application is .007" .001"
[1.78mm .025mm]. Care should be exercised in
selecting the solder paste. The metal purity should
be as high as practical. The flux (in the paste) must
be active enough to remove the oxides formed on
the metallization prior to the exposure to soldering
heat. In practice this can be aided by extending the
solder preheat time at temperatures below the
liquidious state of the solder.
A
B
D
E
F
G
H
Maximum Permissible Power
Dissipation @ + 25
C (Watts)
in free air
Case
Code
0.060
0.075
0.085
0.095
0.110
0.120
0.150
8.2 Soldering: Capacitors can be attached by
conventional soldering techniques, vapor phase,
convection, infrared reflow wave soldering and hot
plate methods. The Soldering Profile charts show
typical recomended time/temperature conditions for
soldering. Preheating is recommended. The
recommended maximum ramp rate is 2C per
second. Attachment with a soldering iron is not
recommended due to the difficulty of controlling
temperature and time at temperature. The soldering
iron must never come in contact with the capacitor.
Temperature
+ 25C
+ 55C
+ 85C
+ 125C
Derating
Factor
1.0
0.9
0.8
0.4
RECOMMENDED REFLOW SOLDERING PROFILE
Recommended SnPb Reflow Soldering Profile
Recommended Pb Free Reflow Soldering Profile
www.vishay.com
135
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
Top
Cover
Tape
Thickness
Embossment
Carrier
Standard orientation is with the
cathode (-) nearest to the sprocket
holes per EIA-481-1 and IEC 286-3.
10,000
10,000
10,000
10,000
4000
5000
2500
Units Per Reel
13" [330]
Reel
7" [178]
Reel
Component
Pitch
Tape
Width
Case
Code
A
B
D
E
F
G
H
2500
2500
2500
2500
1000
1500
600
4mm
4mm
4mm
4mm
8mm
4mm
8mm
8mm
12mm
12mm
12mm
12mm
12mm
16mm
Bending Radius
(Note 2)
R
Min.
Tape and Reel Specifications: All case codes are available on
plastic embossed tape per EIA-481-2. Tape reeling per IEC 286-
3 is also available. Standard reel diameter is 7" [178]. 13" [330]
reels are available and recommended as the most cost effective
packaging method.
The most efficient packaging quantities are full reel increments
on given reel diameter. The quantities shown allow for the sealed
empty pockets required to be in conformance with EIA-481-1 and
EIA-481-2. Reel size and packaging orientation must be specified
in the Vishay Sprague part number.
TAPE AND REEL PACKAGING
in inches [millimeters]
* Pads for B, C and D case codes are otherwise pad compatible with
Type 293D, B, C and D case codes respectively.
REFLOW SOLDER PADS*
in inches [millimeters]
A
B
B
C
PAD
CASE
WIDTH
METALLIZATION
SEPARATION
CODE
(A)
(B)
(C)
A
0.065
0.050
0.040
[1.6]
[1.3]
[1.0]
B
0.065
0.070
0.055
[1.6]
[1.8]
[1.4]
D
0.115
0.070
0.070
[2.9]
[1.8]
[1.8]
E
0.115
0.070
0.120
[2.9]
[1.8]
[3.0]
F
0.150
0.070
0.140
[3.8]
[1.8]
[3.6]
G
0.115
0.070
0.170
[2.9]
[1.8]
[4.3]
H
0.165
0.090
0.170
[4.2]
[2.3]
[4.3]
9.0 Cleaning (Flux Removal) After Soldering: The
695D is compatible with all commonly used solvents
such as TES, TMS, Prelete, Chlorethane.
Solvents containing methylene chloride or other
epoxy solvents should be avoided since these will
attack the epoxy encapsulation material.
10.0 Recommended Mounting Pad Geometries: The
area under the tantalum wire nib should not be
metalised on the PC board. The nib must have
sufficient clearance to avoid electrical contact with
other components. The width dimension indicated is
the same as the maximum width of the capacitor.
This is to minimize lateral movement.
www.vishay.com
136
695D
Vishay Sprague
Document Number 40038
Revision 15-Feb-05
For technical questions, contact tantalum@vishay.com
TAPE AND REEL PACKAGING
Iin inches [millimeters]
Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
USER DIRECTION OF FEED
.030 [0.75]
Min. (Note 3)
Center Lines
of Cavity
.079
.002
[2.0
0.05]
P
1
.030 [0.75]
Min. (Note 4)
Deformation
Between
Embossments
.059 + .004 - 0.0
[1.5 + 0.10 - 0.0]
.069
.004
[1.75
0.10]
.157
.004
[4.0
0.10]
Embossment
W
F
B
0
A
0
Top
Cover
Tape
10 Pitches Cumulative
Tolerance on Tape
0.008 [0.2]
Maximum Cavity
Size (Note 1)
B
1
Max.
(Note 6)
For Tape Feeder
Reference only
including draft.
Concentric around B
0
(Note 5)
Top
Cover
Tape
.004 [0.10]
Max.
.024 [0.600]
Max.
K
0
D
1
Min. For Components
.079 x .047 [2.0 x 1.2] and Larger.
(Note 5)
(Side or Front Sectional View)
Maximum
Component
Rotation
20
T
2
Max.
Notes:
1. A
0
B
0
K
0
are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of
the cavity (A
0
B
0
K
0
) must be within 0.002" [0.05mm] minimum and 0.020" [0.50mm] maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20 degrees for 8mm and 12mm tape. For 16mm tape the clearance must be
within 0.006" [0.15] minimum and 0.035" [0.9] maximum and the clearance must also prevent rotation of the component within the cavity
of not more than 10 degrees.
2. This dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the
embossed cavities or to the edge of the cavity whichever is less. Applies for 8mm and 12mm only.
3. This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the
carrier tape between the embossed cavity or to the edge of the cavity whichever is less. Applies for 8mm and 12mm only.
4. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
embossment location and hole location shall be applied independent of each other.
5. B
1
dimension is a reference dimension for tape feeder clearance only.
A
0
B
0
K
0
TAPE
SIZE
8mm
12mm
12mm
Double Pitch
18mm
B
1
(Max.)
(Note 5)
0.179
[4.55]
0.323
[8.2]
0.323
[8.2]
0.476
[12.1]
D
1
(Min.)
(Note 4)
0.039
[1.0]
0.059
[1.5]
0.059
[1.5]
0.059
[1.5]
F
0.138 0.002
[3.5 0.05]
0.217 0.002
[5.5 0.05]
0.217 0.002
[5.5 0.05]
0.295 0.004
[7.5 0.1]
P
1
0.157 0.004
[4.0 0.1]
0.157 0.004
[4.0 0.1]
0.315 0.004
[8.0 0.1]
0.315 0.004
[8.0 0.1]
T
2
(Max.)
0.098
[2.5]
0.256
[6.5]
0.256
[6.5]
0.315
[8.0]
W
0.315 + 0.012 - 0.004
[8.0 + 0.3 - 0.1]
0.472 0.012
[12.0 0.30]
0.472 0.012
[12.0 0.30]
0.642 Max.
[16.3] Max.
(Note 1)
.039 [1.0]
Max.
3.937 [100.0]
Tape
Camber
(Top View)
Allowable Camber to be .039/3.937 [1/100]
Non-Cumulative Over 9.843 [250.0]
9.843 [250.0]
20
Maximum
Component Rotation
(Top View)
Typical
Component
Center Line
Typical
Component
Cavity
Center Line
B
0
A
0
.039 [1.0] Max.
E
(Min.)
-
-
.
-
0.561
[14.25]
P
2
0.079 0.002
[2.0 0.05]
0.079 0.002
[2.0 0.05]
0.079 0.002
[2.0 0.05]
0.79 0.004
[2.0 0.1]
S
1
(Min.)
-
-
-
0.024
[0.6]
DIRECTION OF FEED
Cathode (-)
Anode (+)
PDF 
ZIP