ChipFind - документация

Электронный компонент: EDI2AG272128V-8.5

Скачать:  PDF   ZIP
EDI2AG272128V
1
White Electronic Designs Corporation (508) 366-5151 www.whiteedc.com
The EDI2AG272128VxxD1 is a Synchronous/Synchronous Burst
SRAM, 72 position DIMM (144 contacts) Module, organized as
2x128Kx72. The Module contains four (4) Synchronous Burst
Ram Devices, packaged in the industry standard JEDEC
14mmx20mm TQFP placed on a Multilayer FR4 Substrate. The
module architecture is defined as a Sync/Sync Burst, Flow-
Through, with support for linear burst. This module provides High
Performance, 2-1-1-1 accesses when used in Burst Mode, and
used as a Synchronous Only Mode, provides a high performance
cost advantage over BiCMOS aysnchronous device architec-
tures.
Synchronous Only operations are performed via strapping ADSC\
Low, and ADSP\ / ADV\ High, which provides for Ultra Fast
Accesses in Read Mode while providing for internally self-timed
Early Writes.
Synchronous/Synchronous Burst operations are in relation to an
externally supplied clock, Registered Address, Registered Global
Write, Registered Enables as well as an Asynchronous Output
enable. This Module has been defined with full flexibility, which
allows individual control of each of the eight bytes, as well as
Quad Words in both Read and Write Operations.
* This data sheet describes a product that may or may not be under development
and is subject to change or cancellation without notice.
FEATURES
s 2x128Kx72 Synchronous, Synchronous Burst
s Access Speed(s): T
KHQV
= 8.5, 9, 10, 12ns
s Flow-Through Architecture
s Linear Burst Mode
s Clock Controlled Registered Bank Enables (E
1
\, E
2
\)
s Clock Controlled Byte Write Mode Enable (BWE\)
s Clock Controlled Byte Write Enables (BW
1
\ - BW
8
\)
s Clock Controlled Registered Address
s Clock Controlled Registered Global Write (GW\)
s Aysnchronous Output Enable (G\)
s Internally self-timed Write
s Gold Lead Finish
s 3.3V
10% Operation
s Common Data I/O
s High Capacitance (30pF) drive, at rated Access Speed
s Single total array Clock
s Multiple Vcc and Vss
July 1998 Rev.
ECO#
2x128Kx72, 3.3V Sync/Sync Burst SRAM SO-DIMM
ADVANCED*
EDI2AG272128V
2
White Electronic Designs Corporation (508) 366-5151 www.whiteedc.com
FUNCTIONAL BLOCK DIAGRAM
PIN CONFIGURATION
DQ
0-63
Input/Output Bus
DQP
0-7
Parity Bits
A
0-16
Address Bus
E
1
\, E
2
\
Synchronous Bank Enables
BWE\
Byte Write Mode Enable
BW
1
-
8
\
Byte Write Enables
CLK
Array Clock
GW\
Synchronous Global Write
Enable
G\
Asynchronous Output Enable
Vcc
3.3V Power Supply
Vss
Ground
NC
No Connect
PIN NAMES
PIN
PIN
PIN
PIN
FUNCTION
FUNCTION
FUNCTION
FUNCTION
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
V
SS
V
SS
A
0
RFU
A
16
A
1
A
2
A
15
A
14
A
3
A
4
A
13
A
12
A
5
A
6
A
10
A
8
V
CC
G\
GW\
ADSP\
E
1
\
E
2
\
BW
1
\
V
CC
DQ
0
DQ
1
DQ
2
DQ
3
V
SS
BW
2
\
V
CC
DQ
8
DQ
9
DQ
10
DQ
11
V
SS
BW
3
\
V
CC
DQ
16
DQ
17
DQ
18
DQ
19
V
SS
BW
4
\
V
CC
DQ
24
DQ
25
DQ
26
DQ
27
V
SS
BW
5
\
V
CC
DQ
32
DQ
33
DQ
34
DQ
35
V
SS
BW
6
\
V
CC
DQ
40
DQ
41
DQ
42
DQ
43
V
SS
BW
7
\
V
CC
DQ
48
DQ
49
DQ
50
DQ
51
V
SS
BW
8
\
V
CC
DQ
56
DQ
57
DQ
58
DQ
59
V
SS
V
SS
DQ
60
DQ
61
DQ
62
DQ
63
V
CC
DQP
7
V
SS
DQ
52
DQ
53
DQ
54
DQ
55
V
CC
DQP
6
V
SS
DQ
44
DQ
45
DQ
46
DQ
47
V
CC
DQP
5
V
SS
DQ
36
DQ
37
DQ
38
DQ
39
V
CC
DQP
4
V
SS
DQ
28
DQ
29
DQ
30
DQ
31
V
CC
DQP
3
V
SS
DQ
20
DQ
21
DQ22
DQ
23
V
CC
DQP
2
V
SS
DQ
12
DQ
13
DQ
14
DQ
15
V
CC
DQP
1
V
SS
DQ
4
DQ
5
DQ
6
DQ
7
V
CC
DQP
0
BWE\
CLK
ADSC\
ADV\
RFU
V
CC
A
9
A
7
A
11
1
2
3
4
5
6
7
8
9
ADSC\
ADSP\
ADV\
BWE\
CLK
G\
GW\
A
0-16
ADSC\
ADSP\
ADV\
BWE\
CLK
G\
GW\
DQ
E\
BW\
E
1
\
BW
1-4
\
ADSC\
ADSP\
ADV\
BWE\
CLK
G\
GW\
DQ
E\
BW\
ADSC\
ADSP\
ADV\
BWE\
CLK
G\
GW\
DQ
E\
BW\
ADSC\
ADSP\
ADV\
BWE\
CLK
G\
GW\
DQ
E\
BW\
U1
U2
U3
U4
E
2
\
BW
5-8
\
DQ
0-31
DQP
0-3
DQ
32-63
DQP
4-7
DQ
32-63
DQP
4-7
DQ
0-31
DQP
0-3
PIN SYMBOLS
EDI2AG272128V
3
White Electronic Designs Corporation (508) 366-5151 www.whiteedc.com
PIN DESCRIPTIONS
DIMM Pins
Symbol
Type
Description
3, 6, 7, 10, 11, 14
A
0-16
Input
Addresses: These inputs are registered and must meet the setup and hold times around the rising edge of CLK. The
15, 18, 19, 20, 17
Synchronous
burst counter generates internal addresses associated with A
0
and A
1
, during burst and wait cycle.
16, 13, 12, 9, 8, 5
33, 47, 61, 75,
BW
1
\, BW
2
\,
Input
Byte Write: A byte write is LOW for a WRITE cycle and HIGH for a READ cycle. BW
0
/ controls DQ
0-7
and DQP
0
, BW
1
\
89, 103, 117,
BW
3
\, BW
4
\,
Synchronous
controls DQ
8-15
and DQP
1
. BW
2
\ controls DQ16-23 and DQP
2
. BW3\ controls DQ
24-31
and DQP
3
. BW
4
\ controls DQ
32-39
131
BW
5
\, BW
6
\,
and DQP
4
. BW
5
\ controls DQ
40-47
and DQP
5
. BW
6
\ controls DQ
48-55
and DQP
6
. BW
7
\ controls DQ
56-64
and DQP
7
.
BW
7
\, BW
8
\
32
BWE\
Input
Write Enable: This active LOW input gates byte write operations and must meet the setup and hold times around the
Synchronous
rising edge of CLK.
25
GW\
Input
Global Write: This active LOW input allows a full 72-bit WRITE to occur independent of the BWE\ and BWx\ lines and
Synchronous
must meet the setup and hold times around the rising edge of CLK.
30
CLK
Input
Clock: This signal registers the addresses, data, chip enables, write control and burst control inputs on its rising edge.
Synchronous
All synchronous inputs must meet setup and hold times around the clock's rising edge.
29, 31
E
1
\, E
2
\
Input
Bank Enables: These active LOW inputs are used to enable each individual bank and to gate ADSP\.
Synchronous
23
G\
Input
Output Enable: This active LOW asynchronous input enables the data output drivers.
26
ADV\
Input
Address Status Processor: This active LOW input is used to control the internal burst counter. A HIGH on this pin
Synchronous
generates wait cycle (no address advance).
27
ADSP\
Input
Address Status Processor: This active LOW input, along with EL\ and EH\ being LOW, causes a new external
Synchronous
address to be registered and a READ cycle is initiated using the new address.
28
ADSC\
Input
Address Status Controller: This active LOW input causes device to be deselected or selected along with new external
Synchronous
address to be registered. A READ or WRITE cycle is initiated depending upon write control inputs.
Various
DQ
0-63
Input/Output
Data Inputs/Outputs: First byte is DQ
0-7
, second byte is DQ
8-15
, third byte is DQ
16-23
, fourth byte is DQ
24-31
, fifth byte is
DQ
32-39
, sixth byte is DQ
40-47
, seventh byte is DQ
48-55
and the eight byte is DQ
56-64
.
34, 48, 62,
DQP
0-7
Input/Output
Parity Inputs/Outputs: DQP
0
is parity bit for DQ
0-7
. DQP
1
is parity bit for DQ
8-15
. DQP
2
is parity bit for DQ
16-23
. DQP
3
is
76, 90, 104,
parity bit for DQ
24-31
. DQP
4
\ is parity bit for DQ
32-39
. DQP
5
is parity bit for DQ
40-47
. DQP
6
\ is parity bit for DQ
48-55
. DQP
7
118, 132
is parity bit for DQ
56-64
and DQP
7
. In order to use the device configured as a 128K x 64, the parity bits need to be tied
to Vss through a 10K ohm resistor.
Various
Vcc
Supply
Core power supply: +3.3V -5%/+10%
Various
Vss
Ground
Ground
EDI2AG272128V
4
White Electronic Designs Corporation (508) 366-5151 www.whiteedc.com
SYNCHRONOUS BURST - TRUTH TABLE
Operation
E1\
E2\
ADSP\
ADSC\
ADV\
GW\
G\
CLK
DQ
Addr. Used
Deselected Cycle, Power Down; Bank 1
H
X
X
L
X
X
X
L-H
High-Z
None
Deselected Cycle, Power Down; Bank 2
X
H
X
L
X
X
X
L-H
High-Z
None
Read Cycle, Begin Burst; Bank 1
L
H
L
X
X
X
L
L-H
Q
External
Read Cycle, Begin Burst; Bank 1
L
H
L
X
X
X
H
L-H
High-Z
External
Read Cycle, Begin Burst; Bank 2
H
L
L
X
X
X
L
L-H
Q
External
Read Cycle, Begin Burst; Bank 2
H
L
L
X
X
X
H
L-H
High-Z
External
Write Cycle, Begin Burst; Bank 1
L
H
H
L
X
L
X
L-H
D
External
Write Cycle, Begin Burst; Bank 2
H
L
H
L
X
L
X
L-H
D
External
Read Cycle, Begin Burst; Bank 1
L
H
H
L
X
H
L
L-H
Q
External
Read Cycle, Begin Burst; Bank 1
L
H
H
L
X
H
H
L-H
High-Z
External
Read Cycle, Begin Burst; Bank 2
H
L
H
L
X
H
L
L-H
Q
External
Read Cycle, Begin Burst; Bank 2
H
L
H
L
X
H
H
L-H
High-Z
External
Read Cycle, Continue Burst; Bank 1
X
H
X
H
L
H
L
L-H
Q
Next
Read Cycle, Continue Burst; Bank 1
X
H
X
H
L
H
H
L-H
High-Z
Next
Read Cycle, Continue Burst; Bank 2
H
X
X
H
L
H
L
L-H
Q
Next
Read Cycle, Continue Burst; Bank 2
H
X
X
H
L
H
H
L-H
High-Z
Next
Read Cycle, Continue Burst; Bank 1
H
H
X
H
L
H
L
L-H
Q
Next
Read Cycle, Continue Burst; Bank 1
H
H
X
H
L
H
H
L-H
High-Z
Next
Read Cycle, Continue Burst; Bank 2
H
H
X
H
L
H
L
L-H
Q
Next
Read Cycle, Continue Burst; Bank 2
H
H
X
H
L
H
H
L-H
High-Z
Next
Write Cycle, Continue Burst; Bank 1
X
H
H
H
L
L
X
L-H
D
Next
Write Cycle, Continue Burst; Bank 1
H
H
X
H
L
L
X
L-H
D
Next
Write Cycle, Continue Burst; Bank 2
H
X
H
H
L
L
X
L-H
D
Next
Write Cycle, Continue Burst; Bank 2
H
H
X
H
L
L
X
L-H
D
Next
Read Cycle, Suspend Burst; Bank 1
X
H
H
H
H
H
L
L-H
Q
Current
Read Cycle, Suspend Burst; Bank 1
X
H
H
H
H
H
H
L-H
High-Z
Current
Read Cycle, Suspend Burst; Bank 2
H
X
H
H
H
H
L
L-H
Q
Current
Read Cycle, Suspend Burst; Bank 2
H
X
H
H
H
H
H
L-H
High-Z
Current
Read Cycle, Suspend Burst; Bank 1
H
H
X
H
H
H
L
L-H
Q
Current
Read Cycle, Suspend Burst; Bank 1
H
H
X
H
H
H
H
L-H
High-Z
Current
Read Cycle, Suspend Burst; Bank 2
H
H
X
H
H
H
L
L-H
Q
Current
Read Cycle, Suspend Burst; Bank 2
H
H
X
H
H
H
H
L-H
High-Z
Current
Write Cycle, Suspend Burst; Bank 1
X
H
H
H
H
L
X
L-H
D
Current
Write Cycle, Suspend Burst; Bank 1
H
H
X
H
H
L
X
L-H
D
Current
Write Cycle, Suspend Burst; Bank 2
H
X
H
H
H
L
X
L-H
D
Current
Write Cycle, Suspend Burst; Bank 2
H
H
X
H
H
L
X
L-H
D
Current
EDI2AG272128V
5
White Electronic Designs Corporation (508) 366-5151 www.whiteedc.com
DC ELECTRICAL CHARACTERISTICS - READ CYCLE
RECOMMENDED DC OPERATING CONDITIONS
ABSOLUTE MAXIMUM RATINGS*
*Stress greater than those listed under "Absolute Maximum Ratings" may cause permanent
damage to the device. This is a stress rating only and functional operation of the device at
these or any other conditions greater than those indicated in operational sections of this
specifications is not implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
Voltage on Vcc Relative to Vss
-0.5V to +4.6V
Vin
-0.5V to Vcc +0.5V
Storage Temperature
-55
C to +125
C
Operating Temperature (Commercial)
0
C to +70
C
Operating Temperature (Industrial)
-40
C to +85
C
Short Circuit Output Current
10 mA
Parameter
Sym
Min
Typ
Max
Units
Supply Voltage
V
CC
3.14
3.3
3.6
V
Supply Voltage
V
SS
0.0
0.0
0.0
V
Input High
V
IH
2.2
3.0
V
CC
+0.3
V
Input Low
V
IL
-0.3
0.0
0.3
V
Input Leakage
IL
I
-2
1
2
A
Output Leakage
ILo
-2
1
2
A
Max
Description
Symbol
Typ
8.5
9
10
12
Units
Power Supply Current
Icc
1
1.6
2.2
2.1
2.1
2.0
A
Power Supply Current
Icc
750
1.5
1.5
1.0
1.0
A
Device Selected,No Operation
CMOS Standby
Icc
3
500
300
300
300
300
mA
Clock Running-Deselect
Icc
K
600
1000
1000
750
750
mA
SYNCHRONOUS ONLY - TRUTH TABLE
Operation
E1\
E2\
GW\
G\
ZZ
CLK
DQ
Synchronous Write-Bank 1
L
H
L
H
L
High-Z
Synchronous Read-Bank 1
L
H
H
L
L
Synchronous Write-Bank 2
H
L
L
H
L
High-Z
Synchronous Read-Bank 2
H
L
H
L
L
AC TEST CIRCUIT
AC TEST CONDITIONS
50
Vt = 1.5V
Output
Z0 = 50
Z0 = 50
Parameter
I/O
Unit
Input Pulse Levels
V
SS
to 3.0
V
Input and Output Timing Levels
1.25
V
Output Test Equivalencies
See figure, at left
AC Output Load Equivalent
1.25V
First
Second
Third
Fourth
Address
Address
Address
Address
(external)
(internal)
(internal)
(internal)
A..A00
A..A01
A..A10
A..A11
A..A01
A..A00
A..A11
A..A10
A..A10
A..A11
A..A00
A..A01
A..A11
A..A10
A..A01
A..A00
BURST ADDRESS TABLE (MODE = V
SS
)
BURST ADDRESS TABLE (MODE = NC/V
CC
)
First
Second
Third
Fourth
Address
Address
Address
Address
(external)
(internal)
(internal)
(internal)
A..A00
A..A01
A..A10
A..A11
A..A01
A..A10
A..A11
A..A00
A..A10
A..A11
A..A00
A..A01
A..A11
A..A00
A..A01
A..A10